咨詢熱線
18948178581
18948178581
美佳特科技
MEIJIATE TECHNOLOGY售前售中售后完整的服務體系
誠信經營質量保障價格合理服務完善 7011-C, 7011-S, 40-channel Multiplexer Cards
7111-S Quad 1×10 Multiplexer Configuration
The Model 7011 40-channel multiplexer has four independent banks of 1×10
switching. Each channel is 2-pole. These four banks can be combined for a
wide variety of switching configurations—for example, dual 1×20, or 1×10 and
1×30, or one large 1×40. The 7001 mainframe can automatically configure
the 7011 to switch 4-pole signals by combining channel pairs. This gives you a
dual 1×10 4-pole multiplexer or a single 1×20 4-pole multiplexer.
Each of the four multiplexer outputs on this card connects to the 7001/7002
mainframes analog backplane through removable jumpers for even greater flexibility. Two mainframes
7011 cards can be used to make a single 1×80 multiplexer with all intercard
connections through the backplane. The 7011 multiplexer outputs can also be
connected to the rows of the 7012 via the backplane for row expansion.
switch The Model 7111-S is a form C?version of the 7011-S. The 7111-S is a low-voltage, switch
quad 1×10, single-pole form C multiplexer card. The 7111-S assembly consists
of a screw terminal connector card and a relay card. External test circuits are
7002 wired directly to the screw terminals of the connector card. 7002
• Quad 1×10 multiplexer for These cards automatically configure the 7001 or 7002 mainframe. Two conn ec
and 2-, 4-, or 8-pole operation tion options are available, screw terminal for maximum flexib ility or a single and
96-pin quick disconnect connector.
7001 • Connects to 7001/7002 7001
backplane for easy
expandability MULTIPLEX CONFIGURATION: Four independent 1×10 2-pole multiplex banks or two independent 1×10 4-pole multiplex banks.
with • 500nV, 100pA offsets Adjacent banks can be connected together. Jumpers can be removed to isolate any bank from the backplane. with
Us e CONTACT CONFIGURATION: 2-pole Form A (Hi, Lo) (1-pole form C for 7111-S). Us e
CONNECTOR TYPE:
Ordering Information 7011-C: 96-pin male DIN connector.
7011-C Quad 1×10 Multiplexer 7011-S and 7111-S: Screw terminal, #16AWG maximum wire size, with 0.092 inch O.D. 28 conductors per card maximum.
#22AWG typical wire size with 0.062 inch O.D. 88 conductors per card maximum.
with 96-pin MAXIMUM SIGNAL LEVEL:
Mass Terminated DC Signals: 110V DC between any two pins, 1A switched. 30VA (resistive load).
Connector Board AC Signals: 125V rms and 175V AC peak, between any two pins, 1A switched, 60VA (resistive load).
7011-S Quad 1×10 Multiplexer COMMON MODE VOLTAGE: 175V peak, any pin to chassis.
with Screw Terminal CONTACT LIFE: Cold Switching: 108 closures. At Maximum Signal Levels: 105 closures.
Connector Board CHANNEL RESISTANCE (per conductor): <1W.
CONTACT POTENTIAL: 7011-C: <1µV per channel contact pair 7011-S, 7111-S: <2µV per contact pair
7111-S Quad 1×10 Form <3µV typical per single contact. <5µV typical per single contact.
C Multiplexer with OFFSET CURRENT: <100pA.
Screw Terminal ACTUATION TIME: 3ms.
Connector Board ISOLATION: HI 7011-C
Bank: >109W, <25pF. Channel 1
Channel to Channel: >109W, <50pF. LO
Accessories Available Bank A Channels 2-9 J
Differential: Configured as 1×10: HI HI HI
For 7011-C: >109W, <100pF. Configured as 1×40: Channel 10 Output J Backplane
7011-KIT-R 96-pin Female Connector Kit >109W, <200pF. LO LO
7011-MTC-1 96-pin Mass Terminated Cable, Female to Common Mode: Configured as 1×10: LO
Female, 1m >109W, <200pF. Configured as 1×40:
SWITCHING AND CONTROL 7011-MTC-2 96-pin Mass Terminated Cable, Female to >109W, <600pF. J J
Female, 2m CROSSTALK (1MHz, 50W Load): Bank: Banks B – C
For 7011-S and 7111-S: <–40dB. Channel: <–40dB.
7011-ST Extra Screw Terminal Connection Board INSERTION LOSS (50W Source, 50W J J
Load): <0.1dB below 1MHz, <3dB
Services Available below 2MHz.
RELAY DRIVE CURRENT (per relay): HI
7011-C-3Y-EW 1-year factory warranty extended to 3 years 7011-C, -S: 16mA Channel 1
from date of shipment 7111-S: 28mA LO
7011-S-3Y-EW 1-year factory warranty extended to 3 years Bank D Channels 2-9 J
from date of shipment HI HI HI
7111-S-3Y-EW 1-year factory warranty extended to 3 years Channel 10 Output J Backplane
from date of shipment LO LO LO
1. 888 .KEITHLEY (U.S. only)
A Greater Measure of Confidence
Mouser Electronics
Authorized Distributor
Click to View Pricing, Inventory, Delivery & Lifecycle Information:
Keithley Instruments, Inc.:
7011-S 7111-S 7011-C 7011-R
